86 lines
2.5 KiB
INI
Executable File
86 lines
2.5 KiB
INI
Executable File
|
|
#hw_mac = 00:a5:b5:ce:d7:f6
|
|
#hw_mac_2 = 00:a5:b5:ce:d7:f7
|
|
|
|
############################################################
|
|
# MAC address
|
|
#
|
|
# Priority 1. From wifi.cfg [ hw_mac & hw_mac_2 ]
|
|
#
|
|
# Priority 2. From e-fuse[ON/OFF switch by wifi.cfg]
|
|
#
|
|
# Priority 3. From insert module parameter
|
|
#
|
|
# Priority 4. From external file path
|
|
# path only support some special charater "_" ":" "/" "." "-"
|
|
#
|
|
# Priority 5. Default[Software mode]
|
|
#
|
|
# 0. => 00:33:33:33:33:33
|
|
# 1. => Always random
|
|
# 2. => First random and write to file[Default path mac_output_path]
|
|
#
|
|
############################################################
|
|
#ignore_efuse_mac = 1
|
|
#mac_address_path = /xxxx/xxxx
|
|
#mac_address_mode = 0
|
|
#mac_output_path = /data/wifimac
|
|
|
|
##################################################
|
|
# Firmware setting
|
|
# Priority.1 insmod parameter "cfgfirmwarepath"
|
|
# Priority.2 firmware_path
|
|
# Priority.3 default firmware
|
|
##################################################
|
|
#firmware_path = /lib/firmware/
|
|
#ignore_firmware_version = 1
|
|
|
|
##################################################
|
|
# Hardware setting
|
|
#
|
|
#volt regulator(DCDC-0 LDO-1)
|
|
#
|
|
#Internal VOLT([MP4-4.2V]-42 [ON BOARD IC-3.3V]-33)
|
|
#
|
|
##################################################
|
|
xtal_clock = 24
|
|
#volt_regulator = 0
|
|
|
|
##################################################
|
|
# Flow control Settings:
|
|
##################################################
|
|
#flowctl = 0
|
|
|
|
##################################################
|
|
# Direct ack Settings:
|
|
# If flowctl = 0, it must turn on the following setting
|
|
# to disable directly ack
|
|
##################################################
|
|
#directly_ack_ctrl = 0
|
|
|
|
##################################################
|
|
# GPIO control Settings: (for low power)
|
|
# 1: pull high
|
|
# 0: pull low
|
|
# GPIO 20 used as wakeup pin, it must set to low.
|
|
##################################################
|
|
sleep_gpio_ctrl = 0x00028018
|
|
dormant_gpio_ctrl = 0x0002b718
|
|
|
|
##################################################
|
|
# BLE Setting
|
|
# if ble_replace_scan_win and ble_replace_scan_interval both are not 0
|
|
# only apply when stack set full scan to link layer
|
|
##################################################
|
|
#ble_replace_scan_win = 0x30
|
|
#ble_replace_scan_interval = 0x0140
|
|
#ble_dtm = 1
|
|
sta_keep_alive_second = 30
|
|
|
|
##################################################
|
|
# Scan Config
|
|
# 0: Scan is not allowed if one of the interfaces is in AP mode and there is STA connected.
|
|
# 1: Scan is allowed no matter in AP mode or STA mode.
|
|
##################################################
|
|
ap_mode_scan_enable = 0
|